Monster Camber Gauge
RPM has combined the most popular genre of R/C – Monster Trucks – with one of the most popular RPM products ever released – the #70992 Precision Camber Gauge. Our Monster Camber Gauge is capable of measuring the camber angle on tires up to 6.5 inches and taller (depending upon the belly height of the tire) and as small as 2 inches in diameter. The Monster Camber Gauge shares all of the same characteristics of its smaller brother – camber accuracy to within ½ of a degree, ease of use, and affordability. Similar to its little brother, the Monster Camber Gauge can measure camber angles way beyond a realistic and usable range (positive or negative 10 degrees!) for universal versatility.

70950 Monster Camber Gauge    

#70950_ - Instructions

Suggested Retail $11.95

Back to Top

Toe-In Gauge

If you are a hobbyist that enjoys R/C vehicles or an all out R/C racer or anywhere in between, this tool is a must for your toolbox! Our toe-in gauge allows you to do trackside checks of the toe angles without removing the wheels! Our gauge checks toe through the simple method of comparing the width of the wheels at the rear of the tire to the width of the wheels at the front of the tire! Our gauge is accurate to within one half of a degree per side and closer! This tool can also be used to check legal width of off-road buggies and trucks. The gauge comes with a second thumbscrew hole to check narrower vehicles such as sedans as well.
Tech Note: RPM recommends using the Toe-In Gauge on any 1/10th scale sedans, buggies, and trucks using 2.2" wheels or smaller. For Monster Truck sized tires, please see our FAQ page here.

70492 Toe-In Gauge    

#70492 - Instructions

Suggested Retail $9.95

Back to Top

Precision Camber Gauge

One of the most critical adjustments on a R/C vehicle is the vehicle’s camber. RPM has proven time after time that even the most experienced drivers cannot set their camber by eye. With our Camber Gauge, novice to professional drivers alike can set their camber on all wheels to less than one degree of accuracy! Once camber has been set and documented, this gauge will be able to tell you if a crash has affected your camber! When used in conjunction with 70492 toe-in gauge, you’ll gain a distinct advantage over anyone that does not have our gauges! Other manufacturers have camber fixtures available but the RPM Precision Camber Gauge is the only one that allows you to do trackside checks in a matter of seconds!
Tech Note: The Precision Camber Gauge is capable of measuring tires with a belly height of 4.5". Monster Truck owners, please consider the RPM #70950 Monster Camber Gauge.

70992 Precision Camber Gauge    

#70992 - Instructions

Suggested Retail $9.95

Back to Top

Ride Height Gauge

RPM designers went all out to create the most innovative and useful tool to check your vehicle’s ride height! (A vehicle’s ride height is the static height of the vehicle as it rests on its suspension. It varies from front to rear and from one side to the other depending upon weight and spring tension.) The gauge has a graduated scale along the upper edge of the base with easy to read lines and numbers. Each graduation on the inch scale (81300) represents 0.025" and on the metric scale (81150), 0.5mm. (for extreme accuracy, the graduations are far enough apart that they may be split to read as little as 0.012" [81300] or 0.25mm. [81150])! Included with the gauge is a spring-loaded tensioning knob to keep the gauge positioned while checking & setting positions on the gauge. The RPM 81300 Ride Height Gauge (inch scale) has a range from 0.150" to 1.150" (5/32" to 1-5/32") and the 81150 Ride Height Gauge (metric scale) has a range from 4mm. to 29.5mm.! RPM’s ingenious design uses a base and a slide that travels along a twenty degree angle. By using such a slight angle, the accuracy of the gauge increases dramatically while still allowing a broad height range. Either gauge may be used to check most on-road or off-road vehicle’s ride height, including pan cars & sedans! It’s extremely easy to use and is the most accurate tool available on the R/C market!

81150 Ride Height Gauge (Metric Scale)    
81300 Ride Height Gauge (Inch Scale)       

#81150 - Instructions

Suggested Retail $8.95

Back to Top