Assoc. GT2, B4 & T4 Mini Front Bumper
Race oriented Associated GT2, B4 & T4 owners prefer lightweight, yet effective parts. That is why RPM is proud to release our Mini Front Bumper for these vehicles. Weighing in at a mere 5-3/4 grams, it is small in size but big on performance. Our mini bumper is 30% thicker than the stock skid plate providing tons of extra skid and impact resistance. The RPM mini bumper extends in front of the vehicle and curves up into a 2” wide bumper that actually performs as a bumper. It protects both the chassis and the hinge pins from frontal impacts and acts as a low-friction skid plate. Similar to our Wide Front Bumpers, our mini bumpers also use all four bulkhead mounting screws to disperse impacts over a larger area reducing transferred impact forces by over 50%! As a finishing touch, our mini bumpers have recessed mounting holes so all those nasty scrapes and crashes will be absorbed by the bumper, not the screws! These bumpers are molded in either blue or black and mount using stock, existing hardware. For the ultimate in bash proof protection, check out our Wide Front Bumper below.

80232	Assoc. GT2, B4 & T4 Mini Front Bumper - Black
80235	Assoc. GT2, B4 & T4 Mini Front Bumper - Blue

Suggested Retail  $4.95

Back to Top

Assoc. GT2, B4 & T4 Wide Front Bumper
The stock front bumper on the Assoc. GT2, B4 & T4 is simply a miniature skid plate. It does nothing to help protect the front end of the vehicle. The RPM wide front bumper for the Assoc. GT2, B4 & T4 was designed to add in loads of bash-proof protection! At a full 6” in width, our bumper can handle some serious abuse! It extends far enough in front of the vehicle to absorb some of the most brutal impacts without transferring the major shock of the impact into the more fragile areas of the vehicle while providing ample front-end chassis skid protection from hard landings. Our front bumper also has strengthening ribs built into it that have a multi-purpose design; The ribs not only add strength to the bumper, but they act as low friction skid rails and they help protect the screw-heads holding the bumper to the bulkheads. The RPM wide front bumper for the GT2, B4 & T4 uses all four bulkhead mounting screws. This helps disperse any impact forces that do make it to the chassis over twice the area of a stock bumper, thereby reducing or eliminating damage to other more fragile areas of the vehicle. RPM bumpers are built using our trademark blend of bulletproof nylons and are molded in black or blue. For the race oriented individual that wants added protection without added weight, we have our Mini Front Bumper available.

80042	Assoc. GT2, B4 & T4 Wide Front Bumper - Black
80045	Assoc. GT2, B4 & T4 Wide Front Bumper - Blue

Suggested Retail  $8.95

Back to Top

Associated GT Receiver Box

Nitro fuel can destroy an expensive receiver in a flash! The only way to protect the receiver is to place it in a protective environment. That’s where RPM steps in. The RPM receiver box is designed to prevent splashes from fuel bottles and nitro cleaner from entering the receiver. Our receiver box is specifically designed to fit in the Associated GT, but can easily fit in any vehicle simply by drilling two mounting holes through the chassis. The RPM receiver box is built from our trademark blend of nylons, guaranteed to withstand most side impacts (protecting your expensive receiver from damage) and is molded in either blue or black. It also has an antenna mount built into the base that helps keep the antenna wire away from other electrical wires which helps prevent glitches. In addition, since our receiver box is built from nylon, which is non-conductive, the receiver is virtually sealed off from glitches emanating from the chassis. The package includes a base and a top to the receiver box, as well as two screws to secure the top to the base and clear and concise instructions for the best possible mount to the chassis. There isn’t any better protection than what RPM has to offer!

Version Compatibility issues: The RPM receiver box will not work with older model GT's using the black, tub style chassis nor will it fit as a stock replacement part on the GT2.

Tech Note: Box interior dimensions are 2.135"L x 1.075"W x 1.4"H. Please measure your receiver prior to purchase for compatibility. 

80052	Assoc. GT Receiver Box - Black
80055	Assoc. GT Receiver Box - Blue

Suggested Retail  $9.95

Back to Top

Associated GT, T2 & 10T Wide Front Bumper

Ready-to-Run vehicles are bringing in a whole new field of individuals into our fine hobby. Most of these RTR vehicles will never see a racetrack. Instead, these drivers are the infamous back-yard bashers we hear about all of the time. They are bouncing their trucks off of trees, curbs, houses, etc. These are the guys that need maximum RPM protection and inspired us to build our wide front bumper for the Associated GT. With a full 6” of width and 1-1/2” of forward extension, our newest basher-proof bumpers will provide that added protection that no one else can offer. Our bumpers are molded in either blue or black and are molded from our guaranteed bulletproof blend of nylons that can take a beating and keep on rolling! For the race-oriented individual, we will still be offering our standard mini front bumpers for the GT (#70711, #70722, #70725, & #70727) that add extra protection over stock bumpers, yet extremely lightweight - perfect for racing.

Tech Note: This bumper does not work on the GT2. Please see this bumper for the GT2 or this bumper for a wide version.

70332	Assoc. GT, T2 & 10T Wide Front Bumper - Black
70335	Assoc. GT, T2 & 10T Wide Front Bumper - Blue

Suggested Retail  $8.95

Back to Top

Associated Elec. TC3 Extended Front Bumper

Demand for protection for the TC3 has been strong for quite some time. RPM is proud to help out with the release of our extended front bumper for the electric TC3. These bumpers add protection like nothing else available! We’ve extended the bumper forward to give added support to the foam bumper as well as extending the width to help protect the front A-arms. In addition, we’ve incorporated our triple buffer-zone system (similar to our NTC3 Front Bumper), which absorbs impact force by allowing the bumper to give slightly during impacts – which translates into reduced stress on the chassis and diff case. The end result – fewer broken parts, fewer lost races from those broken parts, and less stress on the pocket book! Our bumpers are available in blue or black, and are molded from our guaranteed blend of nylons.

80292	Assoc. Elec. TC3 Front Bumper - Black
80295	Assoc. Elec. TC3 Front Bumper - Blue

Suggested Retail  $10.95

Back to Top

NTC3 Impact-Absorbing Front Bumper

If your Associated NTC3 can’t survive a crash, you’ll never make it to the finish line! Stock front bumpers simply can’t handle the punishment that most front-end collisions dish out. That’s where RPM steps in. Our NTC3 front bumper is specifically designed to absorb impacts from front-end collisions with three built-in buffer zones that give slightly under impact to significantly reduce the amount of energy transferred to the more vital and fragile components of the car. No other material (carbon fiber, aluminum, kydex) has the memory capabilities that RPM nylons do, which means that our bumper will return to its original shape after the biggest of crashes! In addition, we guarantee* that our bumpers will not break – which translates into a lifetime of bulletproof front-end protection! Our bumpers are made from our exclusive blend of nylons and are molded in either black or blue. RPM NTC3 front bumpers are a stock replacement and are built to ROAR legal specifications, which means no cutting of the bumper to get it to legal width for racing!

RTR Owners - Please read: The stock front bumper on the RTR is different than the standard kit version NTC3 front bumper. In order to use the RPM NTC3 front bumper, you will need to convert to the standard kit version NTC3 bumper set-up. You will need one Assoc. part #2226 - front bumper / arm mount and the three rubber pads found in Assoc. part #2232.

80272	Associated NTC3 Front Bumper - Black
80275	Associated NTC3 Front Bumper - Blue

Suggested Retail  $10.95

Back to Top

RC10T, T2, & GT Mini Bumper/Skid Plate

The stock bumper does nothing to protect the front end on these trucks! RPM bumpers take impacts without transferring the force into the chassis components. The front edge of this bumper rolls up to give a cushioning effect and prevent the front of the vehicle from digging in off of the jumps. Bolts right on and acts as a front skid plate as well to protect the kick plate and e-clips on the front of the hinge pins. Molded in white Dyeable, Blue, Yellow, or Black nylon.

Tech Note: This bumper does not work on the GT2. Please see this bumper for the GT2 or this bumper for a wide version.

70711	10T, T2 & GT Mini Bumper - Dyeable White
70722	10T, T2 & GT Mini Bumper - Black
70725	10T, T2 & GT Mini Bumper - Blue
70727	10T, T2 & GT Mini Bumper - Yellow

Suggested Retail  $3.95

Back to Top

Snap Tite Body Savers

One of the weakest points on a Lexan body is where the body mounts to the chassis. The holes put in the body for the body posts have a tendency to crack & fracture. This is the reason RPM designed these cool body savers. With their ideal two piece design, it allows one piece to slide through the bottom of the body while the second piece snaps into place from the top of the body. These body savers stay right where you put them, on the body, so you never have to worry about chasing them around! We have found that body life tends to triple when they are installed! Molded from black nylon and sold in a set of five, four for the body mounts & one for the antenna hole! Available in black or white dyeable.

Suggested Retail  $2.95/set of 5

Back to Top

RC10B2 Rear Bumper/Motor Protector

A B2 aluminum motor plate is quite narrow and leaves the endbell portion of the motor exposed to possible damage from rear end collisions or tumbling impacts. RPM has developed a lightweight, rigid, rear "bumper" that attaches to the existing screw holes in the motor plate and extends past the endbell for total protection of the motor! It is injection molded in a durable, ultra lightweight, nylon.

80472	B2, B3, and T3 Rear Bumper - Black
80475	B2, B3, and T3 Rear Bumper - Blue - Discontinued
80477	B2, B3, and T3 Rear Bumper - Yellow

Suggested Retail  $3.95

Back to Top

RC10B2, B3, & T3 Mini Bumper

As technology on the new R/C vehicles gets more & more progressive, the size of the bumpers steadily decreases! RPM still believes that bumpers should act as bumpers, not dirt collectors! Therefore, we designed this bumper to extend 1/2" in front of the arms to help absorb impacts. The leading edge is swept up on a large curve to help prevent dig-ins and is wide enough to protect the hinge-pins and e-clips. The lower skid plate area is double the thickness of the stock bumper for added strength & durability. Molded in RPM's trademark blend of nylon in black, blue, or yellow.

80512	B2, B3, and T3 Mini Bumper - Black
80515	B2, B3, and T3 Mini Bumper - Blue - Discontinued
80517	B2, B3, and T3 Mini Bumper - Yellow

Suggested Retail  $3.95

Back to Top

GT, T2, & RC10T Adjustable Width Body Mounts
This body mounting system allows the racer several choices as to where the mounts may be positioned on the body. The stock position may be retained or a wider setup may be used up front to move the body clips away from the hood cowl. In the rear, RPM has designed reversible mounts that may be used to widen or narrow the rear body mounts, moving the body clips away from the shock tower covers. Molded in our trademark blend of bulletproof nylon, each set comes with two front and two rear body posts, one front chassis mount, two reversible rear shock tower mounts, and molded in black, blue, or yellow.

Tech Note: These body mounts are not compatible with the GT2.

80542	10T, T2 & GT Adjustable Width Body Mounts - Black
80545	10T, T2 & GT Adjustable Width Body Mounts - Blue
80547	10T, T2 GT Adjustable Width Body Mounts - Yellow

Suggested Retail  $6.95

Back to Top